About the journal
Iranian Geological Quarterly
Recent Articles
-
Open Access Article
1 - Determining relationship between lineaments from magnetometry method with copper mineralization in Sabzsang (North of Saveh) deposit based on direct explorations
Reza AhmadiIssue 68 , Vol. 17 , Winter 2024Sabzsang copper deposit is located in the North of Saveh, Markazi province. In this deposit geophysical surveys and extensive surface exploration activities containing litho-geochemical, stream-sediments and trenches sampling have been carried out all over the study are MoreSabzsang copper deposit is located in the North of Saveh, Markazi province. In this deposit geophysical surveys and extensive surface exploration activities containing litho-geochemical, stream-sediments and trenches sampling have been carried out all over the study area. Also, five azimuthal boreholes have been drilled in a square area with dimensions of 100*115 m in the east of the deposit. In this research, lineaments in the Sabzsang deposit were first identified using the magnetometry method. To achieve the goal, the variety of required filters especially edge detection containing horizontal derivative, analytic-signal and tilt derivative was applied on the magnetic data. Afterward, relationship between the lineaments and copper mineralization was investigated using the performed direct explorations. In this regard, the qualitative correlation between the lineaments with surface copper mineralization for the entire area of the Sabzsang was determined, as the qualitative and quantitative correlation between the lineaments with copper mineralization of various surface and deep works in the area of drilling boreholes. The results of the research show that the mineral depositing in the Sabzsang area is mostly shallow, indicating a very high qualitative accordance between the lineaments and occurrence of mineral deposit in the entire surface of the area. To determine the quantitative correlation, first, 2D grid-based map of lineaments was produced. Then, the copper assay data and number of lineaments were interpolated within a same size range after the same gridding. At the end, a very weak correlation with a correlation coefficient of -0.02 was obtained between the copper assay data and lineaments in the eastern part of the deposit. This means that the mineralization has been performed in the dominant fractures but by effecting several factors, the grade of mineral deposit in mentioned locations is not necessarily high. The results of this research serve as a key and guide for decision-making to proceed the detailed exploration stage of the deposit. Manuscript profile -
Open Access Article
2 - A new look at the rotation of Central Iran: A case study of the Anar fault, east block of the Yazd
Hamidreza AfkhamiArdakani farzin ghaemi Fariba Kargaran Bafghi Ahad NouriIssue 68 , Vol. 17 , Winter 2024The Anar fault in the east of Yazd city, with a north-northwest-south-southeast strike, is a basement fault that separates the Yazd block from the Posht Badam block, and its current activity is a dextral strike-slip with a reverse component. The paleostress analysis was MoreThe Anar fault in the east of Yazd city, with a north-northwest-south-southeast strike, is a basement fault that separates the Yazd block from the Posht Badam block, and its current activity is a dextral strike-slip with a reverse component. The paleostress analysis was done on this fault in order to obtain the tectonic history of central Iran in the period from Devonian to Cretaceous. After analyzing 110 fault data in 13 stations of 2 tectonic phases, it was determined that the maximum stress obtained is between the azimuths of 90 to 110 and 190 to 220 and the angle of stress direction changes in the period from Devonian to Cretaceous is 130 degrees. Based on the studies on the barite veins and the dextral displacements that were seen on them, the separation of the stress phases was done, which indicates that the NNE stress direction is older. Further, according to the previous studies of sedimentology and tectonics in central Iran, it was concluded that the cause of this change in tension was the movement towards the northeast along with the 130 degree counter-clockwise rotation of central Iran. Manuscript profile -
Open Access Article
3 - Mineralogy geochemistry and genesis of Kehdolan copper deposit Bostanabad east Azarbaijan
Alireza Yousefi Sh. Niroomand Abdorrahman Rajabi mohammad aminiIssue 68 , Vol. 17 , Winter 2024Study area is located in Eastern Azerbaijan province, 27 km far from east Bostanabad, and the north of Qarehchaman geological map. According to field tracking and surveys, host rock of mineralization is a Subvolcanic rocks of Oligocene period. Based on microscopic studi MoreStudy area is located in Eastern Azerbaijan province, 27 km far from east Bostanabad, and the north of Qarehchaman geological map. According to field tracking and surveys, host rock of mineralization is a Subvolcanic rocks of Oligocene period. Based on microscopic studies, the most important of supergene part, containing primary oxide minerals (Magnetite), secondary oxide minerals (Malachite, Hematite and Goethite) and also sulphide minerals such as Chalcocite, Covellite, Pyrite and insignificance Chalcopyrite. Among the most important alterations, argillic, silicification, carbonization and propylithic can be noted. Geochemical studies shows that host rock of mineralization with Monzosyenitic composition, placed in high chalc-alkaline to shoshonitic and metaluminous range. Formation environment of host rock of mineralization is a volcanic arc of subduction zone that confirmed by normalized rare earth elements diagrams. Manuscript profile -
Open Access Article
4 - Laboratory study of the solubility and resistance of soils near salt domes
Meisam Mahboubi Niazmandi Sohrab MirassiIssue 68 , Vol. 17 , Winter 2024One of the most important potential sources of salinity in southern Iran is the dissolution of salt domes, which in most cases leads to the deterioration of the quality of surface waters, karstic aquifers, and adjacent alluvial aquifers. Although karstic and alluvial wa MoreOne of the most important potential sources of salinity in southern Iran is the dissolution of salt domes, which in most cases leads to the deterioration of the quality of surface waters, karstic aquifers, and adjacent alluvial aquifers. Although karstic and alluvial waters generally have good quality, in many cases in the south of the country, the quality of these waters has decreased due to contact with salt domes. This issue is particularly important in areas such as the lands located on the coasts of the Persian Gulf, where the groundwater level is high. Given that some areas of Hormozgan province, such as Hormuz Island, are composed of salt-susceptible soils with a high percentage of sulfate and gypsum, the occurrence of problems such as subsidence, deviation, and high susceptibility to dissolution is likely. Therefore, this article focuses on examining and evaluating the determination of the susceptibility to dissolution and the resistance characteristics of soils in the areas adjacent to the salt domes on Hormuz Island. The determination of resistance characteristics and susceptibility to dissolution has been carried out based on the results of physical, chemical, technical, and mechanical tests using boreholes and sampling. Some of these characteristics include soil classification, soil moisture content, salt percentage, chloride and phosphate content, maximum density percentage, friction angle, soil cohesion, elasticity modulus, and soil compaction index. The results showed that the presence of salt has led to a decrease in resistance parameters (internal friction angle and cohesion) of the soil. This reduction in cohesion in salt-containing samples compared to natural soil samples without salt has been more pronounced. In addition, the presence of salt leads to an increase in optimal moisture content and a noticeable decrease in maximum dry density of the highly susceptible dissolution soils compared to natural soil samples. Finally, based on the obtained data and the precise identification of susceptible dissolution soils and consideration for future construction in these areas, proposed solutions for preventing and controlling damage to structures on this type of soil have been presented. Manuscript profile
Most Viewed Articles
-
Open Access Article
1 - Introduction of Mari Copper Deposit as a Stratabound Manto-Type Copper Deposit in Tarom Zone, Northwest of Iran
Mehadi Moradi Sajad Maghfori Mohsen Moayyed Vahid FaridaslIssue 38 , Vol. 10 , Summer 2016Similar to other deposits of this type in the world, three major stages could be considered for mineralization in Mari copper deposit. The Mari Copper deposit is located in the northwest of Iran and Tarom metallogenic zone in the north of Zanjan. The ore-body is strata- MoreSimilar to other deposits of this type in the world, three major stages could be considered for mineralization in Mari copper deposit. The Mari Copper deposit is located in the northwest of Iran and Tarom metallogenic zone in the north of Zanjan. The ore-body is strata-bound and hosted by the Eocene mega-porphyritic andesites. The major copper sulfides are bornite, chalcocite, and chalcopyrite associated mainly with pyrite that represent open-space filling, disseminated, vein-veinlet, and replacement textures. The volcanic rocks of the study area mostly represent intermediate to acidic composition with high potassium shoshonitic magmatic series related to intra-arc rift environments. Wall rock alterations include carbonatization, chloritization, epidotization, and sericitization. The abundances of Cu and Ag in fresh mega-porphyritic andesite are up to 3200 and 216 ppm respectively. Based on the main characteristics of Mari ore body such as tectonic setting, host rock, strata-bound form, mineralogy, metal content, and wall rock alterations and comparison of these features with Manto - type copper deposits, Mari Cu deposit can be introduced as a Manto -type Cu deposit in NW Iran. The first stage includes submarine volcanic activity and eruption of mega-porphyritic andesitic lava associated with regional propylitic alteration. In the second stage, the early diagenesis and the activity of sulfate-reducing micro-organisms resulted in the generation of pyrite in the form of open-space filling and disseminated in the mega-porphyritic andesite. Finally, in the third stage, increasing of the thickness of sediments, basin subsidence, and burial diagenesis accompanied with the entry of metal-rich fluids into the reduced host rock, caused the replacement of the first stage pyrites by copper sulfides and mineralization in the Mari deposit. Manuscript profile -
Open Access Article
2 - Assessment of interpretation methods to calculate aquifer transmissivity from single-well step drawdown aquifer test
Hatefi Etebari Delkhahi Gholam Abbas Fanaei Kheirabad ShahsavariIssue 32 , Vol. 8 , Winter 2015Since the measured well drawdowns in a single well test does not reflect the aquifer head loss and covering linear and nonlinear well losses, the calculations based on the observed head loss from a pumping well, cannot get a precise estimate of the hydrodynamic paramete MoreSince the measured well drawdowns in a single well test does not reflect the aquifer head loss and covering linear and nonlinear well losses, the calculations based on the observed head loss from a pumping well, cannot get a precise estimate of the hydrodynamic parameters of the aquifer. But when an inexpensive and rapid estimation of aquifer transmissivity is required, using the collected data from a single pumping well is amongst the attractive options. Several methods for estimating borehole loss components has been proposed by various researchers. In this study, methods proposed by Eden-Hazel, Hantush-Biershenk, Kasinow, Miller-Weber and Karami-Younger; suggesting to calculate well loss component (CQn) were assessed to determine the transmissivity of the aquifer using measured head losses from both the pumping well and the adjacent piezometer from some aquifer tests conducted on a number of exploration wells of Khorasan (Razavi and Southern) provinces. The calculated well loss components using Eden-Hazel, Hantush-Biershenk, Kasenow and Miller-Weber methods has a significant difference to the simulated well losses using piezometric data. Karami-Younger method has been able to calculate the CQn value more accurately, about 25% to the simulated value. However, an accurate CQn estimate did not necessarily concluded to an acceptable aquifer transmissivity calculation. In the other words, the results of implementation of this method is more sensitive in sediments with high permeability and lower well losses. Manuscript profile -
Open Access Article
3 - Comparison of the MLP and RBF Neural Networks for the Determination of Confined Aquifer Parameters
Tahereh Azari Nozar SamaniIssue 36 , Vol. 9 , Winter 2020In this paper, Multi-Layer Perceptron (MLP) and Radial Basis Function (RBF) Artificial Neural Networks (ANNs) are designed for the determination of confined aquifer parameters: transmissibility and storage coefficient. The networks are trained for the well function of c MoreIn this paper, Multi-Layer Perceptron (MLP) and Radial Basis Function (RBF) Artificial Neural Networks (ANNs) are designed for the determination of confined aquifer parameters: transmissibility and storage coefficient. The networks are trained for the well function of confined aquifers. By applying the principal component analysis (PCA) on the training data sets the topology of the MLP and RBF networks is reduced and fixed to [1×12×1] and [1×14×1], respectively regardless of number of records in the pumping test data. The networks generate the optimal match point coordinates for any individual real pumping test data set. The match point coordinates are then incorporated with Theis analytical solution (1935) and the aquifer parameter values are determined. The generalization ability and performance of the developed networks is evaluated with 100000 sets of synthetic data and their accuracy is compared with that of type curve matching technique by two sets of real pumping test data. The results showed that though both MLP and RBF networks are able to determine the confined aquifers parameters and eliminate graphical error inherent in the type curve matching technique but the MLP network is more accurate than the RBF network. Therefore, the proposed MLP network is recommended as an accurate automatic and fast procedure for the confined aquifer parameters estimation. Manuscript profile -
Open Access Article
4 - Seismic hazard assessment of the city of Khoy using deterministic and probabilistic seismic hazard analysis approaches
Nasim Rahmani AbasfamIssue 30 , Vol. 8 , Summer 2014Construction of new cities or development of old towns in an area requires geological and geophysical (seismic) studies. The city of Khoy is one of the developing cities that have to be study. Therefore, the Deterministic and Probabilistic Seismic Hazard Analysis (DSHA MoreConstruction of new cities or development of old towns in an area requires geological and geophysical (seismic) studies. The city of Khoy is one of the developing cities that have to be study. Therefore, the Deterministic and Probabilistic Seismic Hazard Analysis (DSHA and PSHA) approaches have been used to assess seismic hazards and earthquake risk in the city. For this purpose, analyses have been carried out considering historic and instrumented earthquakes, geologic and seismotectonic parameters of the region covering a radius of 100 km with the city of Khoy in the center. Therefore, the main faults and fault zones in the study area were studied and length and distance of each fault from the center of the city of Khoy was calculated. At the next step, the Maximum Credible Earthquake (MCE) and Peak Ground Acceleration (PGA) have been measured using both DSHA and PSHA approaches and also equations presented by different researchers. DSHA Results show that the MCE and PGA values are 6.5 and 0.31g, respectively. PSHA results indicated that the MCE evaluated value is 6.1 for a 0.64 probability in a 50-years period. The period of this earthquake is 110 years and its probability will be 0.009 per a year. The occurrence probability of earthquakes with magnitude equal or greater than 7.1 is 10% and for earthquakes with magnitude equal or greater than 6.3 is 50% for the study area. Manuscript profile -
Open Access Article
5 - Optimization of DRASIC Model for assessment of groundwater vulnerability to nitrate pollution in Kashan Aquifer using statistical methods and sensitivity analysis
faeghe samadiIssue 35 , Vol. 9 , Autumn 2015In this study, the optimized DRASTIC model parameters and land use layer (LU) were used to assess specific vulnerability in Kashan aquifer using statistical methods. Information layers were prepared, rated (deterministic and fuzzy-statistical), weighted (original and st MoreIn this study, the optimized DRASTIC model parameters and land use layer (LU) were used to assess specific vulnerability in Kashan aquifer using statistical methods. Information layers were prepared, rated (deterministic and fuzzy-statistical), weighted (original and statistical) and combined (by Index-Overlay method) in GIS environment. For optimization of DRASTIC model, nonlinear regression for fuzzy-statistical rating (scaling) and Pearson correlation coefficients between nitrate concentrations and scaling parameters of DRASTIC model and sensitivity analysis (removal and single-parameter) were performed to determine and modify weighted parameters. As a result, RASIC-LU model with statistical rating and weighting, single-parameter sensitivity analysis, determined the best selection model based on correlation coefficient = 61.1%, P-Value= 0.001 and with parameters of net recharge, aquifer media, soil media, impact of vadose zone, hydraulic conductivity and land use with weight values of 2.50, 4.63, 4.15, 3.03, 1.96 and 2.00 respectively. According to this model, western and southern parts of the aquifer has a high and very high pollution risk due to high net recharge, pollutant land use and coarse-grain material in the impact of vadose zone, soil and aquifer media. In addition, sensitivity analysis based on mean squares error (MSE) indicated that this model is more sensitive to removal and increase of parameters weight of land use, soil media, impact of vadose zone, aquifer media, net recharge and hydraulic conductivity, and shows a decreasing ternd, respectivily. Manuscript profile -
Open Access Article
6 - Mineralogy, Geochemistry and Alteration of Ore Minerals in Glojeh Epithermal Veins, North of Zanjan
Majid Ghasemi Siani Behzad Mehrabi Mohammad khanaziziIssue 42 , Vol. 11 , Spring 2017The polymetallic epithermal Glojeh ore deposit is located in the middle of the Tarom-Hashtjin metallogenic province in Alborz-Azarbayejan (western Alborz). It consists of four major epithermal veins, in the South Glojeh and the North Glojeh areas. Andesitic basalt and MoreThe polymetallic epithermal Glojeh ore deposit is located in the middle of the Tarom-Hashtjin metallogenic province in Alborz-Azarbayejan (western Alborz). It consists of four major epithermal veins, in the South Glojeh and the North Glojeh areas. Andesitic basalt and dacite are hosting the mineralization in the South Glojeh and the North Glojeh veins, respectively. The in Glojeh area rocks include intrusive rocks (granodiorite, granite and quartzmonzonite), diabasitic dikes, and volcanic rocks (dacite, rhyolite, andesitic basalt and tuff). Based on genetic and crossed relations of vein and vienlets, mineralization in the Glojeh occurs in three stages: (1) early stage of Cu-Au-As-Sb-Fe-bearing minerals; (2) mid stage of Pb-Zn-Cu-Cd-Ag-bearing minerals and (3) late stage of hematite-goethite-Ag-Bi-Au-Pb minerals. Mineralogy and minerals chemistry studies show that galena in stage 2 (substage 2B) have inclusions of silver bearing minerals. Important silver bearing minerals in Glojeh veins are argentite, native silver, Ag-tetrahedrite, polybasite, matildite and marrite. Gold mineralization occured in substage 1B (stage 1), and is associated with specular hematite (specularite) as native gold and in substage 3A (stage 3) as inclusions of native gold and eletrum in hematite and quartz. Alteration in Glojeh district consists of propylilitization, argillization, sericitization and silicification, that have well-developed and zoned in the around Glojeh veins and extends ≈ 30 meters into the host rocks. Chlorite geothermometry in argillic zone (stage 2) and propylitic zone (stage 3) are 275°C and 200°C, respectively. Mass balance calculations indicate that Al, Zr, Ti, Y, Nb, and HREE were immobile elements during alteration. Manuscript profile -
Open Access Article
7 - The Impacts of the North Tabriz Fault on the quantitative and qualitative characteristics of the neighbor aquifer in the East of Tabriz City, Iran
ebrahim rajabpour Abdorreza Vaezi hirIssue 42 , Vol. 11 , Spring 2017The North Tabriz Fault (NTF) is the most prominent tectonic structure in the Northwest of Iran. The results of this study show that this fault has a major impact on hydrogeological conditions of the local aquifer. Plio-Quaternary volcanic ash and tuff layers constitute MoreThe North Tabriz Fault (NTF) is the most prominent tectonic structure in the Northwest of Iran. The results of this study show that this fault has a major impact on hydrogeological conditions of the local aquifer. Plio-Quaternary volcanic ash and tuff layers constitute the only unconfined aquifer of this area which directly lies on Miocene red marl as aquifer bed rock. Northern part aquifer bed rock is placed in the higher level than the southern part. This could be the reason for the existence of the reverse dip-slip movement of fault in this area, which causes the northern part (hanging wall) trust over the southern part (footwall). Sharp differences in aquifer bed rock level at relatively low distances (less than 200 m), can be a sign of near-vertical slope of fault in this area. An obvious groundwater level differences which reaches to more than 8 meters, along with the apparent differences between groundwater qualities across the fault at a low distance (about 200 meters) show a barrier behavior of fault. Total depth of the southern part wells is four times compared to the northern parts. Total annual discharge of southern part wells is about eight times of northern parts. Total hardness and ions concentrations of groundwater samples shows that most of the northern part samples are not suitable for drinking purposes, but the southern part samples are suitable. Also, all of the northern part samples have the negative Langelier index (corrosive). All of the southern part samples have the positive (very close to zero) Langelier index and suitable for industrial usages. Therefore this is a reason why most of industries in this area were located in the southern part of the fault. Manuscript profile -
Open Access Article
8 - Study of mineral chemistry, geothermobarometry and tectonic setting of gabbroic rocks from north-west Hamedan, Iran
عادل ساکی Hooshang Pourkaseb Alireza Zarasvandi Milad Jahani Maryam DoraniIssue 53 , Vol. 14 , Spring 2020The study area is geologically located in the northern area of the Sanandaj-Sirjan metamorphic zone. Based on petrographic study, the main minerals consists of plagioclase, pyroxene, amphibole and biotite and the accessory minerals are chlorite, muscovite, ilmenite and MoreThe study area is geologically located in the northern area of the Sanandaj-Sirjan metamorphic zone. Based on petrographic study, the main minerals consists of plagioclase, pyroxene, amphibole and biotite and the accessory minerals are chlorite, muscovite, ilmenite and zircon. The obtained results from the mineral chemistry in this study indicate that the amphiboles are calcic amphiboles, and in terms of chemical composition they can be called pargasit, tschermakite and magnesiohomblende. Plagioclases are also andesian. Due to the low Na2O content, it can be concluded, that tectonically these amphiboles are of S-Amph type and are related to the subduction zones. Based on the high levels of Al2O3, the origin of amphiboles is mantle-type. Therefore, due to the ratio of Fetot (Fetot + Mg+2) to AlIv, which is less than 0.6, the oxygen fugacity was high. On the other hand, the water levels vary from 2 to 2.3 for hornblende crystallization. Different methods were used to perform thermobarometry, the best of which showed that the formation temperature of gabbroic mass has been in the range of 700°C (in average) and a pressure of 4.45- 7.52 Kb. According to the estimated pressures, the magma was originated at a depth of 25-30 Km, which is near the Moho discontinuity. Manuscript profile -
Open Access Article
9 - Microfacies, Sedimentary Environment and Sequence Stratigraphy of the Qom Formation, Deh Namak, Northwest of Garmsar
Jahanbakhsh Daneshian Asadi Mehmandosti yousef ramezaniIssue 41 , Vol. 0 , Spring 2017Deh Namak section is exposed along the most northern point of the Qom Formation, where the Central Iran zone and Alborz zone come together. The study of microfacies, sedimentary environments and sequence stratigraphic features of the Qom Formation in this area can h MoreDeh Namak section is exposed along the most northern point of the Qom Formation, where the Central Iran zone and Alborz zone come together. The study of microfacies, sedimentary environments and sequence stratigraphic features of the Qom Formation in this area can help to understand the situation of the Qom sedimentary basin in the northern part, bordering the Alborz zone. 166 samples of the Qom Formation in Deh Namak section in the northwest of Garmsar are investigated. Microfacies analysis of these sedimentary rocks indicates that according to sedimentary environment they consist of nine microfacies belonging to four facies belts including tidal flat, agoon, shoal/reef sediments and slope of platform. Due to the absence of the gravitational and turbidity sediments and abundance of reef/shoal sediments, a rimmed carbonate shelf depositional environment is suggested in which more sediments were precipitated in shallow water. In this model, deep facies of the basin did not spread and the deepest facies belong to the slope. Also, sequence stratigraphic studies show that the Deh Namak section is composed of four sedimentary sequences of third- order, two types II and one type I sequence boundaries were recognized in this formation. Manuscript profile -
Open Access Article
10 - Active Tectonics Zonation in Saveh Area, SW Tehran
bijan abdollahi Hossein HajialibeigiIssue 49 , Vol. 13 , Spring 2019Geomorphic indexes can be a useful tool for investigating the impact of active tectonics and the identification of related anomalies, especially in areas that quantitative research work has been done. The study area is a part of the Central Iranian structural-sedimentar MoreGeomorphic indexes can be a useful tool for investigating the impact of active tectonics and the identification of related anomalies, especially in areas that quantitative research work has been done. The study area is a part of the Central Iranian structural-sedimentary zone, located in the Saveh area. By studying the geological and topographic maps and using digital elevation data, it was evaluated the rate of relative active tectonics of this area, using some of the geomorphic indexes such as Hi, Re ,Bs, AF, Vf, Vc, V, SL, Smf and Iat. These indexes which have been measured and compared in eight fronts and nine basins (Shur-payeinii, Lar, Bidlu, Amirabad, Shur-baleii, Eshtehard, Buin Zahra, Arab and Kharrud) resulted to present the active tectonic zonation map for the study area. The measured Hi index shows the relative maturity of all basins and the Arab basin has the most relative tectonic activity compared to other basins. The Re index shows the highest elongation for Lar, Bidlu and Kharrud basins and the least elongation for Shur-payeinii basin. The AF index shows the highest uplift for the Bidlu basin, which is located on the right side of this basin. Vf, Vc and V indexes represent the lowest rate of activity in the valleys which are located on the border between the Shur-baleii and Amirabad basins, the southern part is the Lar basin and the border between Amirabad and Bidlu basins. The Kharrud, Buin Zahra and Arab basins are the most active basins based on the SL index. The Smf index indicates the high activity for all basins. According to active tectonic zonation map, it is possible to show that on the border between the Eshtehard, Shur-baleii, Lar, Bidlu and Amirabad basins which are located in 1 class, have the highest degree of activity. These basins are affected by behavior Jaru, Gomorkan, Ipak, Takidagh, and Alishar faults. Other parts along the mountain fronts are also located in 2 class and are active. The low-lying areas (Kharrud, Buin Zahra and Arab basins) located in 3 class, have the least degree of activity. The highest rate of SL index is for Kharrud, Buin Zahra and Arab basins. This high rate resulted to the seismic and active Ipak fault. According to Smf index, Amirabad basin is the most active basins. Vf index represent the lowest rate which are located on the border between the Shur-baleii and Amirabad basins. This border is located on Jaru and Gomorkan faults. Manuscript profile